Home > Error Code > Image Hot Tub Error Codes

Image Hot Tub Error Codes

Contents

Heat Related Pump Not Primed. Adding cool water may be necessary. Low Water Flow (LF, FLO), is the usual cause of an overheating (OH, OHH) spa or hot tub. These Codes are Control System Manufacturer SpecificTo determine your Spas control manufacturer look at the systems electronic control box cover (front or back) for the manufacturer.Note: Some Spa assemblers have their navigate here

No Automatic Functions will turn ON during this time, and the Heater will Not Start. Blocked Skimmer.4. Wird geladen... Contact your Dealer or Service Organization.A Sensor Failure Message may indicate Excessively High Heater Temperatures which can Scald or Burn!If the Heater is Not Cool Enough to Safely Service, allow the see here

Balboa Hot Tub Error Codes

Melde dich an, um dieses Video zur Playlist "Später ansehen" hinzuzufügen. Could be a dirty filter, a clogged impeller, closed valve, or a piece of plastic film covering the spa drain. All Rights Reserved.

  1. With the system powered off, you normally unscrew the sensors from the heater manifold, and unplug the wire from the panel.
  2. Other issues that can cause these error codes one or more of the service valves is not open up all the way.
  3. Heater disabled but the spa is operational.
  4. SE = Spa operating in Standard-in-Economy Mode.
  5. Any and all service should be performed by a licensed spa technician.
  6. Topside controls also give lots of information about your spa status, which are not to be confused with spa error codes.
  7. The idea is that, if anything in the file changes, the checksum will change and Result in a CrC Error.At Power-Up, the System has Failed the Program Checksum Test.

If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. Melde dich bei YouTube an, damit dein Feedback gezählt wird. If the Spa with the "SF" Safety Fault Error Message has a pump suction blockage switch, Select "Spas with Pump Suction Blockage Switch" Below. Marquis Spa Error Codes at heater.OHS = Overheat.

Back to Top SnS or Sn Message SnS or Sn MessageIf the SnS or Sn Message is Alternating with the Water Temperature on the Display, it is a Possible Sensors Out Vita Spa Error Codes Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. The Spa or Hot Tub Panel Displays: SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Again these can be caused by a flow issue.

Blocked Suction Fitting.3. Great Lakes Hot Tub Error Codes The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. Email Address: Password: You will be prompted to enter your password on the next page Create an account Forgot Password? System will Auto Reset when Water Temp is below 108°F (42.2°C).

Vita Spa Error Codes

I WAS SO IMPRESSED WITH HOW QUICK YOU ANSWERED MY QUESTIONS (ON A WEEKEND ESPECIALLY, WOW!!)" - Cheryl, Lake Stevens, WA "I don't know if u guys monitor this email address http://www.hottubworks.com/blog/spa-hot-tub-error-codes-oh-ohh-omg/ Du kannst diese Einstellung unten ändern. Balboa Hot Tub Error Codes Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). How To Fix Flo Error Hot Tub All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 365 Days, but some Spa Brands or Models may be Different.

Spa Overheating Troubleshooting Flow Chart Here's a Cal Spa troubleshooting flow chart that has some other possible triggers of seeing OH, OHS, OHH or HH blinking on your spa panel. check over here Categories Consumer Research for Best Hot Tub (99) hottubworks.com (126) life (130) spa chemicals (67) spa covers (160) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Hi Limit Sensor Failure. The first thing and most important thing to try is to restart your Arctic Spa by turning the breaker off and on again. Hot Tub Error Code Oh

Wiedergabeliste Warteschlange __count__/__total__ How to repair hot tub error code SN3 diy collaborative AbonnierenAbonniertAbo beenden328328 Wird geladen... Blocked Suction Fitting.3. Leave a Reply Click here to cancel reply. his comment is here After about 45 Seconds, Check for Error Messages on the Topside Panel Display.

Clean or replace your spa filter cartridge as a first step. Coleman Spa Error Codes In some instances it may be more prudent to contact a local repairman or send Spa Care Center your control box for evaluation/repair. Wird geladen...

If there is No Error Message, Select "No Error Message" Below.

Too Many Closed Jets.6. Brett Spa Side Error Codes OH : Temp exceeds 118 degrees Fr : Freeze condition - temp below 40 degrees FL : Pressure switch failure EO : Shorted temp sensor E1 Press Any Button to Reset and Clear the Error Message.3. Coast Spa Error Codes Press Any Button other than "Jets 1" to Exit Drain Mode and Standby Mode, and Return to Normal Operation.

Snb = Spa is shut down. The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles. For Low Flow spa error codes, check the filter, check the pump and check the valves to find something that is obstructing the water flow. http://colvertgroup.com/error-code/icacls-error-codes.php drops.HL = High limit switch tripped.

Anmelden Transkript Statistik 38.133 Aufrufe 32 Dieses Video gefällt dir? Once again these can be caused by a flow issue. Inspect the wires for any heat or rodent damage, and the sensor face for corrosion or scaling. System will restart when temp.

Back to Top OHS, OH, or SPA TEMP LMT Message There is an "Over Heated Spa" (OHS or OH) Water Condition.One of the Water Temp Sensors has detected 110°F (43.3°C) Incoming Wenn du bei YouTube angemeldet bist, kannst du dieses Video zu einer Playlist hinzufügen. After about 45 Seconds, Check for Error Messages on the Topside Panel Display. Melde dich an, um dieses Video zur Playlist "Später ansehen" hinzuzufügen.

Transkript Das interaktive Transkript konnte nicht geladen werden. Depending on where the temp sensor is mounted; usually in the wall of the spa in a sensor mount, you could have a flow issue. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. Do not let the pumps run for a total of more than 2 minutes if they haven't primed by then.

Or, it could be a problem with the thermostat allowing the heater element overheat. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? Open the spa cover to allow excess heat and steam to escape. Switch closed while pump is deactivated.

Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature.--- = "Watchdog". FL2 = Pressure switch problem.